Youth Adjustable SUP Paddle

Description

Interlux Nautical ProGuard Ablative Antifouling Paint

Sold in gallons

Interlux Nautical ProGuard Ablative is performance, value and reliability all in one. ProGuard Ablative is an all-purpose, low V.O.C. antifouling paint formulated to erode away with use reducing paint build-up. ProGuard Ablative provides season-long protection in moderate to high fouling waters and can be applied directly over most properly prepared antifouling paints. Recommended for use on the underwater areas of fiberglass, wood, and properly primed metal (except aluminum) boat hulls and can be used in fresh, salt and brackish waters.

• Reliable performance at an excellent value
• Reduced paint build-up
• Season-long protection in moderate to high fouling waters
• Compatible over most antifouling paints
• Low V.O.C.

Specifications:

• Finish: Matte
• Coverage: 455 sq. ft/gal
• Number of Coats: 2 coats, 3 on bare wood
• Application Method: Brush, roller, airless and conventional spray

Do not use on aluminum

***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***

How to Apply

APPLICATION DATA METHOD: Airless Spray, Brush, Conventional Spray, Roller

NUMBER OF COATS: 2, 3 on bare wood

DRY FILM THICKNESS PER COAT:2 mils (3.6 mils wet)

COVERAGE: 455 sq. ft/gal.

APPLICATION TEMP: 41F Min. / 95F Max.

THINNER: Thin 10% wuth Xylene. Do not exceed 10 % by volume.

DRY TIMES:

Temp	To Touch	To Recoat	To Launch
95F	1 HR	8 HR	8 HR
73F	2 HR	12 HR	12 HR
50F	3HR	16 HR	16 HR

PREVIOUSLY PAINTED SURFACES – GOOD CONDITION: Remove all traces of loose paint by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene using the two-rag method before and after sanding. Apply two coats of ProGuard Ablative allowing for appropriate dry times.

PREVIOUSLY PAINTED SURFACES – POOR CONDITION: Completely remove old antifouling paint, after all old antifouling paint has been completely removed, sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene using the two-rag method before and after sanding. Apply two coats of ProGuard Ablative allowing for appropriate dry times.

BARE FIBERGLASS: scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry. Remove mold release wax and surface contamination by wiping down the surface with Xylene using the two-rag method. Fill any surface imperfections with approved filler for underwater use. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with Xylene using the two-rag method. Apply two coats of ProGuard Ablative allowing for appropriate dry times.

BARE WOOD:Sand the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene using the two-rag method before and after sanding. Apply the first coat of ProGuard Ablative thinned 10% with Xylene. Apply two finish coats of ProGuard Ablative allowing for appropriate dry times

UNDERWATER METALS: Apply an approved underwater metal primer as per manufacturers instructions. Apply two coats of ProGuard Ablative allowing for appropriate dry times. Do not use on aluminum

APPLICATION METHODS:

Mixing: Stir well before use.
Cleaner: Acetone or Xylene
Thinning: Thin 10% with Xylene Do not exceed 10% by volume.
Ventilation and Humidity Control: Apply in dry, well ventilated conditions.

Roller: Use a 3/8″ nap solvent resistant roller.
Airless Spray: Tip Size: 0.53-0.66 mm/21-26 thou. Pressure: 170-204 bar/2500-3000 psi.
Conventional Spray: Pressure Pot: Tip Size: 1.8-2.2 mm/70-85 thou. Pressure: 4.08-4.76
bar/60-70 psi (gun pressure); 10-15 psi (pot pressure).

Click here to download Interlux Nautical ProGuard Ablative Antifouling Paint

California Residents:
WARNING
Cancer and Reproductive Harm –
P65Warnings.ca.gov

Other Details

Google Product Type:
Antifouling
Wiser:
Yes
Paint Type:
Ablative Antifouling
Number of Seasons:
Single Season
Antifouling Type:
Copper Based
Hull Material:
Fiberglass, Steel, Wood
Water Type:
Brackish Water, Fresh Water, Salt Water